Jam Nut 3/4 Bore 16 TPI Right Hand Thread. Rock Krawler Suspension's service parts are a direct replacement for your existing hardware. Please measure carefully to ensure proper fitment.

• 1-1/8 Inch head width
• Corrosion resistant zinc coating
• 3/4 Inch bore
• 16 TPI
• Right hand thread
• Universal fitment
• Sold individually
• Made in the USA

Jam Nut 3/4 Bore 16 TPI Left Hand Thread. Rock Krawler Suspension's service parts are a direct replacement for your existing hardware. Please measure carefully to ensure proper fitment.

• 1-1/8 Inch head width
• Corrosion resistant zinc coating
• 3/4 Inch bore
• 16 TPI
• Left hand thread
• Universal fitment
• Sold individually
• Made in the USA

Small Joint Retainer 3/4 and 7/8 Krawler Joints. Rebuild part for 3/4 inch and 7/8 inch Krawler Joint.
Features:

• Rebuild part for 3/4 inch and 7/8 inch Krawler Joint
• Sold In Pairs

Large Joint Retainer 1, 1-1/4 and 1-3/8 Krawler Joints
Features:

• Rebuild part for 1 inch and 1 1/4 inch Krawler Joint
• Sold In Pairs

Rock Krawler JL Rear Spring Pad Correction 18-Pres Wrangler JL
Includes:
(2) JL rear spring correction pad

Rear Coil Spring Correction Wedges 07-Present Wrangler JK/JK Unlimited
Our polyurethane rear coil spring correction wedges will fix the following:

• rear coil spring bowing
• poor handling due to loss of effective spring rate
• rear coil spring and rear track bar contact

Includes:
(2) Rear coil spring correction wedges.

Sway Bar Strap Kit. Hold your sway bar out of the way with The Rock Kralwer Sway Bar Straps. Retains the sway bar and links up and out of the way of axle movement.
Includes:

• (2) Sway Bar Straps
• Hardware, and instruction.

Gussets Upper C's-Dana 30/44 Axles Front 07-Present Wrangler JK/JK Unlimited
Our Upper C Gussets:

• Are 5/16 inch Thick
• Strengthen weak factory upper C's
• Fit both Dana 30 and Dana 44 front axle housings
• Tie into the spring mounting pads
• Removal of the upper ball joints is not required

Includes:
(2) 5/16 thick steel upper C gussets.

Rock Krawler JL Front Spring Pad Correction 18-Pres Wrangler JL
Includes:

• (2) JL Front spring correction pad
• For use with aftermarket JL springs

Designed to easily mount a PSC Remote Reservoir Setup into a 2007-11 Jeep JK with a MOPAR HEMI Engine Conversion.

The Rock Krawler weld on rear cradle tie in plate is a great way to add style and strength to our Rock Krawler weld on rear cradle. It is made from 1/4 inch thick laser cut steel!
System Benefits:

• Adds style to the rear axle assembly when our weld on cradle is used
• Adds strength to the rear cradle for exceptional hard core use

System Includes:
(1) Rear cradle tie in plate made from 1/4 inch thick laser cut steel.
Notes:
Works great with the Rock Krawler weld on rear cradle part number RK00533. May require trimming depending upon what axle it is being used with.

Edelmann High Pressure Hose Assembly for 1997-2002 Jeep TJ.

Features:

• 44.5 Inches Long
• Edelmann power steering pressure hose covers are highly resistant to oil, heat and ozone which cause ordinary assemblies to fail prematurely.
• Hose construction withstands internal oil temperatures of up to 300 degrees Fahrenheit.
• High-tensile strength braided fabric helps Edelmann pressure hoses withstand pulsation pressures up to 1,500 psi and bursting pressures that exceed 6,000 psi.
• Tubing is coated with a Zinc-Aluminum Alloy with an Aluminum-Rich Epoxy topcoat, and the couplings and fittings are zinc-plated for rust and corrosion protection.

Pro Krawler Joint 3/4 Inch Shank Right Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

• Universal fitment
• Corrosion resistant zinc coating
• Fully machined Chromoly joint housing
• 14 TPI
• Right hand thread
• 14 MM bolt bore
• 2.625 mounting width
• Sold individually
• Jam nuts sold separately
• Made in the USA

Pro Krawler Joint 3/4 Inch Shank Left Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

• Universal fitment
• Corrosion resistant zinc coating
• Fully machined Chromoly joint housing
• 14 TPI
• Left hand thread
• 14 MM bolt bore
• 2.625 mounting width
• Sold individually
• Jam nuts sold separately
• Made in the USA

Pro Krawler Joint 3/4 Inch Shank Right Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

• Universal fitment
• Corrosion resistant zinc coating
• Fully machined Chromoly joint housing
• 14 TPI
• Right hand thread
• 14 MM bolt bore
• 2.375 mounting width
• Sold individually
• Jam nuts sold separately
• Made in the USA

Pro Krawler Joint 3/4 Inch Shank Left Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

• Universal fitment
• Corrosion resistant zinc coating
• Fully machined Chromoly joint housing
• 14 TPI
• Left hand thread
• 14 MM bolt bore
• 2.375 mounting width
• Sold individually
• Jam nuts sold separately
• Made in the USA

Pro Krawler Joint 3/4 Inch Shank Right Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

• Universal fitment
• Corrosion resistant zinc coating
• Fully machined Chromoly joint housing
• 14 TPI
• Right hand thread
• 10 MM bolt bore
• 1.95 mounting width
• Sold individually
• Jam nuts sold separately
• Made in the USA

Pro Krawler Joint 3/4 Inch Shank Left Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

• Universal fitment
• Corrosion resistant zinc coating
• Fully machined Chromoly joint housing
• 14 TPI
• Left hand thread
• 10 MM bolt bore
• 1.95 mounting width
• Sold individually
• Jam nuts sold separately
• Made in the USA

Pro Krawler Joint 3/4 Inch Shank Right Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

• Universal fitment
• Corrosion resistant zinc coating
• Fully machined Chromoly joint housing
• 14 TPI
• Right hand thread
• 12 MM bolt bore
• 2 mounting width
• Sold individually
• Jam nuts sold separately
• Made in the USA

Pro Krawler Joint 3/4 Inch Shank Left Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

• Universal fitment
• Corrosion resistant zinc coating
• Fully machined Chromoly joint housing
• 14 TPI
• Left hand thread
• 12 MM bolt bore
• 2 mounting width
• Sold individually
• Jam nuts sold separately
• Made in the USA

Pro Krawler Joint 7/8 Inch Shank Right Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

• Universal fitment
• Corrosion resistant zinc coating
• Fully machined Chromoly joint housing
• 14 TPI
• Right hand thread
• 14 MM bolt bore
• 2.375 mounting width
• Sold individually
• Jam nuts sold separately
• Made in the USA

Pro Krawler Joint 7/8 Inch Shank Left Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

• Universal fitment
• Corrosion resistant zinc coating
• Fully machined Chromoly joint housing
• 14 TPI
• Left hand thread
• 14 MM bolt bore
• 2.375 mounting width
• Sold individually
• Jam nuts sold separately
• Made in the USA

Pro Krawler Joint 7/8 Inch Shank Right Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

• Universal fitment
• Corrosion resistant zinc coating
• Fully machined Chromoly joint housing
• 14 TPI
• Right hand thread
• 12 MM bolt bore
• 2 mounting width
• Sold individually
• Jam nuts sold separately
• Made in the USA

Pro Krawler Joint 7/8 Inch Shank Left Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

• Universal fitment
• Corrosion resistant zinc coating
• Fully machined Chromoly joint housing
• 14 TPI
• Left hand thread
• 12 MM bolt bore
• 2 mounting width
• Sold individually
• Jam nuts sold separately
• Made in the USA

Pro Krawler Joint 7/8 Inch Shank Right Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

• Universal fitment
• Corrosion resistant zinc coating
• Fully machined Chromoly joint housing
• 14 TPI
• Right hand thread
• 14 MM bolt bore
• 2.625 mounting width
• Sold individually
• Jam nuts sold separately
• Made in the USA

Pro Krawler Joint 7/8 Inch Shank Left Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

• Universal fitment
• Corrosion resistant zinc coating
• Fully machined Chromoly joint housing
• 14 TPI
• Left hand thread
• 14 MM bolt bore
• 2.625 mounting width
• Sold individually
• Jam nuts sold separately
• Made in the USA

Pro Krawler Joint 7/8 Inch Shank Right Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

• Universal fitment
• Corrosion resistant zinc coating
• Fully machined Chromoly joint housing
• 14 TPI
• Right hand thread
• 10 MM bolt bore
• 1.95 mounting width
• Sold individually
• Jam nuts sold separately
• Made in the USA

Pro Krawler Joint 7/8 Inch Shank Left Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

• Universal fitment
• Corrosion resistant zinc coating
• Fully machined Chromoly joint housing
• 14 TPI
• Left hand thread
• 10 MM bolt bore
• 1.95 mounting width
• Sold individually
• Jam nuts sold separately
• Made in the USA

Pro Krawler Joint 7/8 Inch Shank Right Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

• Universal fitment
• Corrosion resistant zinc coating
• Fully machined Chromoly joint housing
• 14 TPI
• Right hand thread
• 12 MM bolt bore
• 2 mounting width
• Sold individually
• Jam nuts sold separately
• Made in the USA

Pro Krawler Joint 7/8 Inch Shank Left Hand Thread. The Pro Krawler Joint is a revolutionary joint manufactured with the tightest tolerances for ultimate consistency. The chromoly joint housings are heat treated for increased strength and then zinc plated for corrosion resistance. The hard chrome plated inner ball is machined from billet 52100 steel for strength and durability. The inner raceway provides wear resistance, high frequency vibration isolation and durability. The body and clevis mounting width ratio of the Pro Krawler Joint is a key design feature which provides up to plus and minus 30 degrees of misalignment. That's a total of 60 degrees of misalignment per side.

• Universal fitment
• Corrosion resistant zinc coating
• Fully machined Chromoly joint housing
• 14 TPI
• Left hand thread
• 12 MM bolt bore
• 2 mounting width
• Sold individually
• Jam nuts sold separately
• Made in the USA